How to Make Proper Pruning Cuts

Make Every Cut Count

Every cut is a wound the tree has to live with. Trees don't heal the way we do; they seal off damaged wood and grow new wood over it. A cut in the right place lets that happen quickly. A cut in the wrong place can open the trunk to decay for life. Here's how our ISA Certified Arborists make cuts that follow ANSI A300, the national standard for tree pruning, and how you can do the same on small branches at home.

Start With a Reason for Every Cut

Before the saw comes out, decide why a branch is coming off. Good reasons include dead or diseased wood, rubbing branches, limbs over the roof or driveway, and a young tree with two competing tops. Leaves make the tree's food, so taking off live branches without a purpose costs the tree energy. As a rule of thumb, the International Society of Arboriculture (ISA) advises removing no more than about a quarter of the live crown at one time, and less on mature trees.

Find the Branch Collar

Look where a branch joins the trunk. You'll usually see a slightly swollen ring of bark at the base of the branch, called the branch collar, and a raised line of bark in the crotch above it, called the branch bark ridge. Inside the collar is a natural chemical barrier that helps keep decay from spreading into the trunk. The correct removal cut sits just outside the collar, angled away from the branch bark ridge.

Don't cut flush with the trunk. A flush cut slices through the collar, makes a bigger wound and removes the tree's defense zone. The bark above and below a flush cut often dies back.

Don't leave a stub. A long stub can't be closed over by new wood, so it dies, rots and gives decay a path into the trunk.

On dead branches, the collar sometimes grows out along the limb. Cut just beyond the living collar and leave it intact.

The Three-Cut Method for Large Limbs

A heavy limb cut in one pass from the top will often tear as it falls, stripping a long strip of bark down the trunk. That tear is a far bigger wound than the cut itself. The three-cut method prevents it:

1. Undercut. About 12 to 18 inches out from the trunk, cut upward from the underside of the limb, about a third of the way through, or until the saw starts to pinch. This stops a tear from running back toward the trunk.

2. Top cut. A little farther out than the undercut, or directly above it, cut down through the limb from the top. The weight drops away cleanly and leaves a short stub.

3. Final cut. Remove the stub with one clean cut just outside the branch collar. With the weight gone, nothing tears.

Colorado State University Extension suggests using this method on anything larger than about an inch across.

Reduction Cuts Instead of Topping

To make a tree shorter or narrower, an arborist uses reduction cuts: a branch or leader is cut back to a side branch big enough to take over, generally at least one-third the diameter of the stem being removed. The tree keeps its natural shape and grows normally from that new leader.

Heading cuts, where a branch is chopped back to a stub or a tiny twig, are what topping is made of. They trigger a burst of fast, weakly attached sprouts, and those sprouts are more likely to break later. ANSI A300 does not treat topping as an acceptable pruning practice. If your tree has outgrown its space, the right answer is careful reduction over time, or sometimes replacing it with a better-suited tree.

Skip the Wound Paint

Pruning sealers and tree paint feel like they should help, but research summarized by ISA shows dressings don't reduce decay or speed up wound closure. Most arborists don't use them. A clean cut in the right spot is the best treatment there is.

Why We Disinfect Our Tools Between Trees

Saws and pruners can carry disease from one tree to the next on sap and sawdust. Two diseases make this especially important in Orange County:

Fusarium dieback, the fungus spread by invasive shot hole borers. UC IPM recommends disinfecting pruning tools between trees to avoid spreading it.

Fusarium wilt of Canary Island date palms. There's no cure, and UC Cooperative Extension says it spreads on pruning saws. They recommend sanitizing tools before each palm and using a hand saw rather than a chainsaw, because a chainsaw is so hard to clean.

When to Call a Pro

Small branches you can reach from the ground with hand pruners or a pole saw are fine for a careful homeowner. Anything that needs a ladder, a chainsaw or a climb belongs to a trained, insured crew. Large limbs are heavy and move in unexpected ways.

Our arborists climb with ropes and harness on trees that are staying, never spikes, and wear full PPE on every job. See our tree trimming & pruning service for what's included.

Watch the Three-Cut Method

Undercut, top cut, then a final cut just outside the branch collar.

Need a Tree Pruned the Right Way?